GA10-D - Alberta Slip Black Cone 10R

Modified: 2017-06-21 13:54:32

You can make a black glaze at cone 10R using only 1% black stain in a 100% calcine:raw mix of Alberta Slip

Material	Amount
Alberta Slip	50.00
Alberta Slip 1000F Roasted	50.00
Added
Mason 6666 or 6600	1.00
101.00

Notes

Alberta Slip is a great base for black glazes at cone 10 reduction, only 1% black stain is needed to obtain a jet black glossy. Increasing amounts of stain up to 5% move toward a matte black for Mason 6600 (they remain glossy for Mason 6666). Adding 5-10% black stain and 5-7% iron produces a crystalizing intense gunmetal black. Mixtured additions of Mason 6600:6666 (e.g. 1:1, 2:2) produce metallic surfaces.

Like other high-percentage Alberta Slip glazes, you must use a mix of calcined a raw powder. See the preparation page at http://albertaslip.com for more information.

Related Information

Alberta Slip as a base for glossy black glazes at cone 10R

A jet a black glossy glaze for cone 10R is as easy as 1% black stain and 99% Alberta Slip (Mason 6666 or 6600). Of course, the 99% is a mix of calcine and raw material (starting at 50:50).

A metallic, silky crystal black glaze based on Alberta Slip

This is a 50:50 mix of calcine and raw Alberta Slip plus 5 parts Mason 6600 black stain, 5 Mason 6666 black and 7 iron.

Cone 10R Gunmetal black glaze made using Alberta Slip

A 50:50 mix of raw and roasted Alberta Slip with 5% Mason 6666 stain added. The slurry was ball milled. Fired at cone 10R.

Additions of black stain to Alberta Slip at cone 10R

Alberta Slip (50:50 calcine:raw mix) with 1, 2, 3, 4 and 5% added Mason 6666 black stain. Fired at cone 10R. Semi-gloss blacks are produced. Increasing stain percentage above about 3% does not darken the color appreciably.

Roasting Alberta and Ravenscrag Slips at 1000F: Essential for good glazes

Roasted Alberta Slip (right) and raw powder (left). These are thin-walled 5 inch cast bowls, each holds about 1 kg. I hold the kiln at 1000F for 30 minutes. Why do this? Because Alberta Slip is a clay, it shrinks on drying (if used raw the GA6-B and similar recipes will crack as they dry and then crawl during firing). Roasting eliminates that. Calcining to 1850F sinters some particles together (creating a gritty material) while roasting to 1000F produces a smooth, fluffy powder. Technically, Alberta Slip losses 3% of its weight on roasting so I should use 3% less than a recipe calls for. But I often just swap them gram-for-gram.

Links

Firing Schedules	Plainsman Cone 10R Firing Six-step oxidize-at-end schedule to 2372F
Recipes	GA10-B - Alberta Slip Tenmoku Cone 10R You can make a tenmoku from Alberta Slip by adding only 2% iron oxide and 5% calcium carbonate
Typecodes	Alberta Slip Glaze Recipes Alberta Slip is a substitute for Albany Slip that has gained a life of its own so that there are now many glazes based specifically on it.
Materials	Alberta Slip Albany Slip successor - a plastic clay that melts to dark brown glossy at cone 10R, with a frit addition it can also host a wide range of glazes at cone 6.

XML to Paste Into Desktop Insight

<recipes>XML not functional: We are working on this problem.</recipes>

By Tony Hansen
Follow me on

Got a Question?

Buy me a coffee and we can talk